If you are, and you specify "Allow access", a user will be able to use multiple methods to gain access to your system. I can't go over all of the various permutations in a single article, however. These are the steps needed on the server to get a VPN up and running. Of course, if you have devices such as firewalls between your VPN server and the Internet, further steps may be required; these are beyond the scope of this article, however.
Figure B The summary screen is pretty basic for this role Take note: This selection just starts another wizard called the Routing and Remote Access Wizard, described further below.
The Routing and Remote Access Wizard component. Editor's Picks. The best programming languages to learn in Check for Log4j vulnerabilities with this simple-to-use script. TasksBoard is the kanban interface for Google Tasks you've been waiting for. Paging Zefram Cochrane: Humans have figured out how to make a warp bubble. Show Comments. Hide Comments. My Profile Log out. Join Discussion. Add your Comment.
Click to clear the Activate the default response rule check box, and then click Next. Click Finish leave the Edit check box selected. The IPSec tunnel is made up of two rules. Each rule specifies a tunnel endpoint. Because there are two tunnel endpoints, there are two rules. The filters in each rule must represent the source and destination IP addresses in IP packets that are sent to that rule's tunnel endpoint.
In the new policy properties, click to clear the Use Add Wizard check box, and then click Add to create a new rule. Type an appropriate name for the filter list, click to clear the Use Add Wizard check box, and then click Add. Click the Protocol tab. Make sure that the protocol type is set to Any , because IPSec tunnels do not support protocol-specific or port-specific filters.
If you want to type a description for your filter, click the Description tab. It is generally a good idea to give the filter the same name that you used for the filter list. The filter name appears in the IPSec monitor when the tunnel is active.
Click the IP Filter List tab, and then click to select the filter list that you created. Click the Tunnel Setting tab, click The tunnel endpoint is specified by this IP Address box, and then type 3rdextip where 3rdextip is the IP address that is assigned to the non-Microsoft gateway external network adapter. Click the Filter Action tab, click to clear the Use Add Wizard check box, and then click Add to create a new filter action because the default actions allow incoming traffic in clear text. Keep the Negotiate security option enabled, and then click to clear the Accept unsecured communication, but always respond using IPSec check box.
You must do this for secure operation. Note None of the check boxes at the bottom of the Filter Action dialog box are selected as an initial configuration for a filter action that applies to tunnel rules.
Only the Use session key perfect forward secrecy PFS check box is a valid setting for tunnels if the other end of the tunnel is also configured to use PFS.
Click Add , and keep the Integrity and encryption option selected or you can select the Custom for expert users option if you want to define specific algorithms and session key lifetimes. Click OK. Click the Authentication Methods tab, configure the authentication method that you want use preshared key for testing, and otherwise use certificates. Kerberos is technically possible if both ends of the tunnel are in trusted domains, and each trusted domain's IP address IP address of a domain controller is reachable on the network by both ends of the tunnel during IKE negotiation of the tunnel before it is established.
But this is rare. Any outbound traffic on the interface type that matches the filters tries to be tunneled to the tunnel endpoint that is specified in the rule.
Inbound traffic that matches the filters is discarded because it must be received secured by an IPSec tunnel. Click the Filter Action tab, and then click to select the filter action that you created. Click the Authentication Methods tab, and then configure the same method that you used in the first rule the same method must be used in both rules.
Click OK , make sure both rules that you created are enabled in your policy, and then click OK again. A green arrow appears in the folder icon next to your policy. To see the active filters, type the following command at a command prompt:. If you want to prevent traffic that does not have a source or destination address that matches NetA or NetB , create an output filter for the external interface in the Routing and Remote Access MMC so that the filter drops all traffic except packets from NetA to NetB.
Click Do not dial the initial connection if the computer is permanently connected to the Internet. Click Next. Click Anyone's use if you want to permit any user who logs on to the workstation to have access to this dial-up connection.
Click My use only if you want this connection to be available only to the currently logged-on user. Click Properties to continue to configure options for the connection. To continue to configure options for the connection, follow these steps:. Click Start , point to Connect to , and then click the new connection. If you don't currently have a connection to the Internet, Windows offers to connect to the Internet.
When the connection to the Internet is made, the VPN server prompts you for your user name and password. Type your user name and password, and then click Connect. Your network resources must be available to you in the same way they're when you connect directly to the network.
To disconnect from the VPN, right-click the connection icon, and then click Disconnect. Cause : The name of the client computer is the same as the name of another computer on the network. Solution : Verify that the names of all computers on the network and computers connecting to the network are using unique computer names.
For more information about how to turn on the remote access server, see the Windows Server Help and Support Center. For more information about how to configure ports for remote access, see the Windows Server Help and Support Center. For more information about how to view properties of the remote access server, see the Windows Server Help and Support Center.
To do so, click Ports in Routing and Remote Access. Cause : The VPN client and the VPN server in conjunction with a remote access policy aren't configured to use at least one common authentication method. Solution : Configure the VPN client and the VPN server in conjunction with a remote access policy to use at least one common authentication method. For more information about how to configure authentication, see the Windows Server Help and Support Center. Cause : The VPN client and the VPN server in conjunction with a remote access policy aren't configured to use at least one common encryption method.
Solution : Configure the VPN client and the VPN server in conjunction with a remote access policy to use at least one common encryption method. For more information about how to configure encryption, see the Windows Server Help and Support Center. Cause : The VPN connection doesn't have the appropriate permissions through dial-in properties of the user account and remote access policies.
Solution : Verify that the VPN connection has the appropriate permissions through dial-in properties of the user account and remote access policies. For the connection to be established, the settings of the connection attempt must:. For more information about an introduction to remote access policies, and how to accept a connection attempt, see the Windows Server Help and Support Center. Cause : The settings of the remote access policy profile are in conflict with properties of the VPN server.
The properties of the remote access policy profile and the properties of the VPN server both contain settings for:. Which edition of Windows server Meanwhile, Please take time to read the link below:.
Tiger Li. Office Office Exchange Server. Not an IT pro? Resources for IT Professionals. Sign in. United States English. Ask a question.
0コメント